Skip to main content

FOUR - STROKE , OTTO CYCLE , SPARK IGNITION ENGINE

Hello friend's so in this post we will talk about four strock engines.

The modern petrol ( gasoline ) engines operate on Otto ( constant volume ) cycle . This cycle was introduced in practical form by a German scientist Otto in 1876 , although it was described by a French scientist Beande Roches in 1862. In a four - stroke Otto cycle , spark ignition engine , the four strokes are as follows :

1. Suction stroke During suction stroke , the piston is moved downward by the crankshaft , which is revolved either by the momentum of the flywheel or by the power generated by the electric starting motor . The inlet valve remains open and the exhaust valve is closed during this stroke . The downward movement of the piston sucks air - fuel mixture in the cylinder from the carburettor through the open inlet valve . Here the fuel is petrol mixed with air , broken up into a mist and partially vaporized in the carburettor . 


2. Compression stroke  During compression stroke , the piston moves upward , thus compressing the charge . Ignition and much of the compression also take place during this stroke . The heat produced by the compression makes more homogeneous mixture of air and petrol inside the cylinder . The heat makes the petrol easier to burn while the compression forces it into closer combination with the air.
The mixture, under compression, is ignited by the spark produced by a spark plug and the combustion is about half - completed when the piston is at top dead center. Both the inlet and exhaust valves remain closed during the compression stroke.


3. Working, Power or Expansion stroke  The expansion of the gases due to the heat of combustion exerts a pressure on the cylinder and piston. Under this impulse the piston moves downward thus doing useful work. Both the valves remain closed during this stroke. 
 
4. Exhaust stroke  During this stroke, the inlet valve remains closed and the exhaust valve opens. The greater part of the burnt gases escapes because of their own expansion. The piston moves upwark and pushes the remaining gases out of the open exhaust valve. Only a small quantity of exhaust gases remains in the clearance space which will dilute the fresh incoming charge.
 
Thus, in this type of engine, four strokes of the piston are required to complete the cycle, and the four strokes make two revolutions of the crankshaft. The operations are repeated over and over again in running the engine. Each alternative revolution of the crankshaft has one power stroke.

Comments

Post a Comment

Popular posts from this blog

VALVE TIMING DIAGRAM OF A FOUR-STROKE, OTTO CYCLE ENGINE

Hello friend's in this post we will talk about valve timing diagram of a four stroke, otto cycle engine It has already been explained in the operation of four stroke, Otto cycle engine that the inlet valve opens during the suction stroke and the exhaust valve opens during the exhaust stroke. The exact moment at winch each of the valves opens and closes with reference to the position of piston and crank can be shown graphically in a diagram. This diagram is known as valve timing diagram. Theoretically, the inlet valve opens exactly at the beginning of suction stroke and closes at the end of the stroke. Both the valves remain closed during compression and power strokes. The exhaust valve opens exactly at the beginning of exhaust stroke and closes at the end of stroke. The theoretical valve timing diagram for a four-stroke Otto cycle engine is shown in Fig. 3.3. The opening and closing of valves with reference to the position of piston and crank shaft during the four strok...
Post a Comment
Read more

Carl Freidrich Benz inventor self propulsion

Hello friend's, so in this post we will talk about Carl Freidrich Benz. Carl Friedrich Beauz was born on November 25, 1844 in Carlsruhe.  His father was Germany's first engine driver.  His mother wanted him to become a civil servant because it was a safe prototype but Carl Benz decided to go to the Polytechnic College in Karlsruhe. After completing his engineering studies, he found an apprenticeship "like apprenticeship" employing his words in an engineering factory, by 1871 Benz decided that he had gained enough experience to open his own workshop. For the first few years he managed to accomplish both ends by manufacturing and selling building requirements in his "Mechanical Workshop".  His spare time was devoted to the work he was genuinely interested in building a two-stroke engine.  Benz built a light-weight but powerful combustion engine to replace horses, which, although expensive to acquire and maintain, was the only form of road traction, the "s...
Post a Comment
Read more

Petrol Engine (Gasoline Engine)

Hello friend's in this post we talk about Petrol Engine. The engine which gives power to propel the modern Indian automobile is a petrol-burning, spark-ignition four-stroke cycle, internal combustion engine. Petrol is a liquid fuel and is called by the name gasoline in America. That is why the petrol engines are also known as gasoline engines. The ability of petrol to furnish power rests on the two basic principles of physics:  1. Burning or combustion is always accompanied by the production of heat.  2. When a gas is heated, it expands. If the volume remains constant, the pressure rises according to Charle's law.  The operation of petrol engine in the production of power may be described as follows:  During the downward motion of the piston, the air fuel mixture is sucked from the carburettor into the cylinder. During the upward motion the mixture is compressed by the piston in the cylinder and ignited by an electric spark. When the mixture is burned in the cylinde...
1 comment
Read more